Are you building a Mud Monster or a Pavement Princess??
If so you can have your own thread in this section.
This section on other websites has led to arguments and contention. People are posting pictures of their pride and joy and therefore CONSTRUCTIVE comments only please!
If so you can have your own thread in this section.
This section on other websites has led to arguments and contention. People are posting pictures of their pride and joy and therefore CONSTRUCTIVE comments only please!
Dave's "S200KYS" Jimny 'laner Build...
- Shima
- New Member
-
Public
29 May 2014 09:50 #116585
by Shima
Replied by Shima on topic Dave's (Bits4Vits) Jimny 'laner Build...
Looking good Dave, when you installing it? 
You have a week left
You have a week left
- supergaz
- New Member
-
Public
29 May 2014 19:14 - 29 May 2014 19:16 #116625
by supergaz
Replied by supergaz on topic Dave's (Bits4Vits) Jimny 'laner Build...
Girrrr Mines SORN'D again, But i've some sweet mods to do If I ever get time off work now i'm back from Florida.
The Rockwatt cradle is a work of art almost too nice to stick under the jimny :silly:
If I ever get time off work now i'm back from Florida.The Rockwatt cradle is a work of art almost too nice to stick under the jimny :silly:
Last edit: 29 May 2014 19:16 by supergaz.
- Bits4Vits
- Topic Author
- New Member
-
Public
30 May 2014 09:31 - 30 May 2014 09:39 #116648
by Bits4Vits
Replied by Bits4Vits on topic Dave's (Bits4Vits) Jimny 'laner Build...
Quick update, got an email from the ORA last night, to confirm my roll hoop before they bend it up 
Dimensions are in inches as they use american computer based bending software and machinery...
Hope i've measured it right!
As my Jimny is a soft-top with a hard-top fitted to the rear, I thought it wise to take the precaution of fitting a roll hoop and stays, it will be sandwiched through the floor with these feet plates from the ORA too...
Dimensions are in inches as they use american computer based bending software and machinery...
Hope i've measured it right!
As my Jimny is a soft-top with a hard-top fitted to the rear, I thought it wise to take the precaution of fitting a roll hoop and stays, it will be sandwiched through the floor with these feet plates from the ORA too...
Last edit: 30 May 2014 09:39 by Bits4Vits.
- Bits4Vits
- Topic Author
- New Member
-
Public
02 Jun 2014 21:54 - 02 Jun 2014 21:55 #116949
by Bits4Vits
Replied by Bits4Vits on topic Dave's (Bits4Vits) Jimny 'laner Build...
And today it turned up with a carrier -
The ends of they stays have been notched ready for welding to the top crossbar...
... and the feet -
With sandwich plates under the floor -
Looks like I was half an inch out with my sketch!
So I just need to cut a little off the bottom of the feet tubes, and weld the X-cross pieces onto the foot plates, and I'm done... get it tacked, welded up, and then off for powder-coating...
MANY THANKS TO THE ORA!
The ends of they stays have been notched ready for welding to the top crossbar...
... and the feet -
With sandwich plates under the floor -
Looks like I was half an inch out with my sketch!
So I just need to cut a little off the bottom of the feet tubes, and weld the X-cross pieces onto the foot plates, and I'm done... get it tacked, welded up, and then off for powder-coating...
MANY THANKS TO THE ORA!
Last edit: 02 Jun 2014 21:55 by Bits4Vits.
03 Jun 2014 04:04 #116964
by Halford
Replied by Halford on topic Dave's (Bits4Vits) Jimny 'laner Build...
that's a nice dog guard 
Time to create page: 0.189 seconds