×
BigJimnyMeet (North) 2024 (12 Jan 2024)
BigJimnyMeet 2024
14th July 2024
Parkwood Nr. Leeds
14th July 2024
Parkwood Nr. Leeds
Booking now open - Discount for additional vehicles
Click HERE for details
Click HERE for details
×
A place for more technical discussions. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.
Gen 3 - Engine Stalling at low revs - Service Bulletin
11 Feb 2023 12:02 - 11 Feb 2023 12:06 #247560
by mlines
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Gen 3 - Engine Stalling at low revs - Service Bulletin was created by mlines
Looking through the Suzuki Jimny bulletins, I found this one from March 2019 for Gen3 Jimnys (so the bulletin was released after the Gen3 was discontinued). I believe it applys to all Jimnys from 2008 but it may evne extend to 2005 (introduction of the VVT)
"Engine stalling may occur when pulling away from standstill using minimal accelerator pedal input."
This applies to both Manual and Automatic vehicles. If you think your Jimny stalls too easily then there is a software update for ECU,
This aoplies to ECU:
33920-76JB*
33920-76JC*
33921-76JA*
33921-76JB*
33921-76JL*
33921-76JM*
33922-76J7*
33922-76J8*
33922-76JG*
33922-76JH*
As ALL gen3 are out of warranty this upgrade would cost you, It is timed as a 40 minute activity on the Bulletin.#
"Engine stalling may occur when pulling away from standstill using minimal accelerator pedal input."
This applies to both Manual and Automatic vehicles. If you think your Jimny stalls too easily then there is a software update for ECU,
This aoplies to ECU:
33920-76JB*
33920-76JC*
33921-76JA*
33921-76JB*
33921-76JL*
33921-76JM*
33922-76J7*
33922-76J8*
33922-76JG*
33922-76JH*
As ALL gen3 are out of warranty this upgrade would cost you, It is timed as a 40 minute activity on the Bulletin.#
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Last edit: 11 Feb 2023 12:06 by mlines.
The following user(s) said Thank You: Lambert, Darthblaker7474
Please Log in or Create an account to join the conversation.
15 Feb 2023 10:52 #247629
by RainerK
Replied by RainerK on topic Gen 3 - Engine Stalling at low revs - Service Bulletin
Thank you very much for this information.
Could you also give the number of the service bulletin?
Thank you!
Could you also give the number of the service bulletin?
Thank you!
Please Log in or Create an account to join the conversation.
15 Feb 2023 11:22 #247630
by mlines
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Replied by mlines on topic Gen 3 - Engine Stalling at low revs - Service Bulletin
Q-SN-012
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
The following user(s) said Thank You: RainerK
Please Log in or Create an account to join the conversation.
Time to create page: 0.092 seconds