× A place for more technical discussions. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.

Breather Kit / Electronic Solenoid shift Transfer Box ???

  • X8GGY
  • X8GGY's Avatar Topic Author
  • Offline
  • Site Sponsor
  • Site Sponsor
    Registered
  • Suzukis - a life long obsession!
More
25 Jul 2020 15:52 #225638 by X8GGY
Anyone out there got an electronic / solenoid / button shift transfer box, with a breather kit on it?

I just had this photo sent by an eBay customer -



Which shows a "rubber hose" installation of a breather kit... but there's a T-piece and another hose going off to a breather on what I presume is the solenoid / actuator on a push button transfer box?...

Any experience folks?

Is that buggy finished yet?...
Attachments:

Please Log in or Create an account to join the conversation.

More
25 Jul 2020 16:29 #225639 by jackonlyjack
The following user(s) said Thank You: X8GGY

Please Log in or Create an account to join the conversation.

  • X8GGY
  • X8GGY's Avatar Topic Author
  • Offline
  • Site Sponsor
  • Site Sponsor
    Registered
  • Suzukis - a life long obsession!
More
25 Jul 2020 16:42 #225640 by X8GGY
Thanks JOJ ;)

Is that buggy finished yet?...

Please Log in or Create an account to join the conversation.

More
25 Jul 2020 19:43 #225649 by sniper
Yes Dave, as Jack says, just done it.

Top breather for the transfer case used a 1/8th BSP 90 push fit to a push fit T. The T goes to the shift actuator and the manifold...

I'd get a picture but it's very wet, will do it in the morning if needed....

sniper
The following user(s) said Thank You: X8GGY

Please Log in or Create an account to join the conversation.

More
26 Jul 2020 00:04 - 26 Jul 2020 00:07 #225660 by HUN
I should have seen this post before but I was busy in the garage. I was still under my car an hour ago...
Push fit breather kit is installed to my button operated transfer box.
bigjimny.com/index.php/forum/18-build-th...0-transfer-box-flush
Only difference to Sniper's setup is that I did leave the tiny breater pipe (actuator) as it came from the facory, and only connected the top breather with push fit system.

TrailMaster 2" lift kit
JB rear disk brake conversion, all guards, recovery points & battery tray
ORE transfer box HD brackets
T-Max split charge system
X-Shock Dakar ceramic clutch kit & roof rack
Flo-Flex castor polybushes
Kumho KL71 tyres
AVM hubs
ORA radius arm guards
Push-fit breathers
Last edit: 26 Jul 2020 00:07 by HUN.
The following user(s) said Thank You: X8GGY

Please Log in or Create an account to join the conversation.

  • X8GGY
  • X8GGY's Avatar Topic Author
  • Offline
  • Site Sponsor
  • Site Sponsor
    Registered
  • Suzukis - a life long obsession!
More
26 Jul 2020 16:05 #225701 by X8GGY
Thanks guys! B)

He's bought the kit, plus an add-on for the transfer box, and two gearbox add-ons, so as Sniper indicates, he's going to use a T-piece and a short section of tube to go to the actuator breather like in the rubber hose photo above...

I'll ask him if he'll take a photo of it when it's fitted... :)

Is that buggy finished yet?...

Please Log in or Create an account to join the conversation.

Time to create page: 0.083 seconds
Powered by Kunena Forum

I hope you enjoy using this forum. Please consider making a donation towards the upkeep of this forum website.

We use cookies to give you the best online experience. Please let us know if you agree to all of these cookies. Accepting the Cookies also accepts the Disclaimers for the website.