×
A place for general chat about the Jimny. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.
Suppliers/Dealers or anyone selling with a commercial view in mind CANNOT post here unless responding to a specific request of a member in a "wanted" post.
Suppliers include people "breaking for spares" on a regular basis, when purchasing spares members should ask a supplier what they contribute to the running of the forum particularly if contacted by a Private Message
Suppliers or Members who have contributed to the forum can be identifed by the
logo.
Suppliers/Dealers or anyone selling with a commercial view in mind CANNOT post here unless responding to a specific request of a member in a "wanted" post.
Suppliers include people "breaking for spares" on a regular basis, when purchasing spares members should ask a supplier what they contribute to the running of the forum particularly if contacted by a Private Message
Suppliers or Members who have contributed to the forum can be identifed by the
Re:What did you do to your jimny today?
10 Feb 2013 12:24 #61890
by nicho
03 plate, + 2 inch kap springs, es3000 shocks, offset wheels, Malatesta Kaiman 215 80 15s, rear shock relocators. k&n pannel filter.trimmed arches and bumpers.big jimny shock nuts bolts.disco steering damper.
Replied by nicho on topic What did you do to your jimny today
put charged up battery back on, started it drove it back and forth on drive parked in a different place so dont get flat spots on tyres ,when revs were low after a few minutes bat light came on soon as u give sightly more revs it goes off. 
03 plate, + 2 inch kap springs, es3000 shocks, offset wheels, Malatesta Kaiman 215 80 15s, rear shock relocators. k&n pannel filter.trimmed arches and bumpers.big jimny shock nuts bolts.disco steering damper.
Please Log in or Create an account to join the conversation.
10 Feb 2013 17:44 #61964
by GuardianAngel
Marix Puma 215/75/15 MT's|2" lift|ORA radius arm guards|Fixed hubs|Asfir fuel tank guard|JB Tbox guard|K & N filter|ORA winch plate
Replied by GuardianAngel on topic Re: What did you do to your jimny today
Fitted one front disk and set of pads before freezing rain stopped play 
Marix Puma 215/75/15 MT's|2" lift|ORA radius arm guards|Fixed hubs|Asfir fuel tank guard|JB Tbox guard|K & N filter|ORA winch plate
Please Log in or Create an account to join the conversation.
10 Feb 2013 18:21 #61980
by dirtydogz
2002 JLX Soft Top
Jimnybits 2" lift +Pro Comp ES1000 shocks.
Big Jimny rear shock mounts. Big Jimny adjustable panhard rods.
Big Jimny steering damper bracket. Disco Armstrong steering damper. 7X15 black modulars. 205/75/15 Maxxis 743 bravo m/t.Superpro camber correction bushes.Black A bar....
Replied by dirtydogz on topic Re: What did you do to your jimny today
Ok it was time to change the kingpins so it was off down to Martins (BIG JIMNY SHOP) to pick up two new sets of king pins bearings+oil seals + waterproof grease + copper silicone sealant.
This was my first time at replacing the king pins, so I down loaded the (how to? guide) from this forum and printed it off, then I just got on with doing the job.
I even removed the bolts on the backing plate, so I could copper grease the bolts as you need to remove them if your are place the wheel bearings at a later date (you can do the job with out removing the bolts and leave the back plate in place .)
I've only replaced the driver's side at the moment as that side was leaking oil and the weather was so bad, rain and snow.
The top bearing was OK but the lower one was a right mess some of the top of the bearing was missing so the bearing started to disintegrate, here are some photos to look at,so if yours are leaking oil this is the time to replace them.
The job the takes about 2 hour and that was my first go at doing the kingpins, so if you have a go just take your time.
This was my first time at replacing the king pins, so I down loaded the (how to? guide) from this forum and printed it off, then I just got on with doing the job.
I even removed the bolts on the backing plate, so I could copper grease the bolts as you need to remove them if your are place the wheel bearings at a later date (you can do the job with out removing the bolts and leave the back plate in place .)
I've only replaced the driver's side at the moment as that side was leaking oil and the weather was so bad, rain and snow.
The top bearing was OK but the lower one was a right mess some of the top of the bearing was missing so the bearing started to disintegrate, here are some photos to look at,so if yours are leaking oil this is the time to replace them.
The job the takes about 2 hour and that was my first go at doing the kingpins, so if you have a go just take your time.
2002 JLX Soft Top
Jimnybits 2" lift +Pro Comp ES1000 shocks.
Big Jimny rear shock mounts. Big Jimny adjustable panhard rods.Big Jimny steering damper bracket. Disco Armstrong steering damper. 7X15 black modulars. 205/75/15 Maxxis 743 bravo m/t.Superpro camber correction bushes.Black A bar....
Please Log in or Create an account to join the conversation.
10 Feb 2013 18:56 #61991
by fast forward
if you cant go round it go over it ! or vice versa ?
Replied by fast forward on topic Re: What did you do to your jimny today
thats good going started to do mine and couldnt get some bolts out even after heating them up then came up against the ABS sensor and wire couldnt get this bolt out either bolt head corroded and rounded off . so put it all back together with the new discs and pads will leave king pins till a later date gave snow warning out so need car ! 
if you cant go round it go over it ! or vice versa ?
Please Log in or Create an account to join the conversation.
10 Feb 2013 22:21 #62064
by jimnybob
Replied by jimnybob on topic Re: What did you do to your jimny today
changed side light bulbs
Please Log in or Create an account to join the conversation.
Time to create page: 0.596 seconds