A place for more technical discussions. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.
g16b into a jimny - what parts do I need
- darthloachie
- Topic Author
- New Member
-
Public
03 Sep 2014 09:23 #123286
by darthloachie
g16b into a jimny - what parts do I need was created by darthloachie
Hi all
Just bought a g16b engine out of a grand vitara gv1600 thats done 54k which comes complete as in the picture
what do I need to fit it into my g13b jimny?
do i need a gearbox adapter plate? if so where from?
what do I need to keep from the jimny engine?
thanks in advance
Chris
Just bought a g16b engine out of a grand vitara gv1600 thats done 54k which comes complete as in the picture
what do I need to fit it into my g13b jimny?
do i need a gearbox adapter plate? if so where from?
what do I need to keep from the jimny engine?
thanks in advance
Chris
Please Log in or Create an account to join the conversation.
- Cider
- New Member
-
Public
- darthloachie
- Topic Author
- New Member
-
Public
03 Sep 2014 19:38 #123316
by darthloachie
Replied by darthloachie on topic g16b into a jimny - what parts do I need
Thanks Pete 
Please Log in or Create an account to join the conversation.
03 Sep 2014 19:56 #123321
by j999pre
Gold Jimny the best colour (sold)
Big red Jimny 32" tyres, arbs, cage 5:1 transfer etc. (Sold)
Grey pick up Jimny
Turbo m13a, arbs, floating rear shafts, disc conversion rear, vented front conversion. 245 70 16. Winch, 3" lift, 4:16 trans hd shafts and CVS
Replied by j999pre on topic g16b into a jimny - what parts do I need
I bought the adapter and engine mount from water babies.
Swap your crank pulley
Inlet manifold but use the gv injectors
Swap mounts. Also water pipe from rear of pump. Make a little bracket.
Power steering tensioner has a few solutions. Done lower the bottom 2 holes on a plate. Others just chop the top bit off so it just mounts with the lower holes. I use the lower holes and re weld the top piece to pic up the top hole.
Water feeds for heater and your about there
The adapter I used was for the sj so needed the bottom on each side cutting off
Swap your crank pulley
Inlet manifold but use the gv injectors
Swap mounts. Also water pipe from rear of pump. Make a little bracket.
Power steering tensioner has a few solutions. Done lower the bottom 2 holes on a plate. Others just chop the top bit off so it just mounts with the lower holes. I use the lower holes and re weld the top piece to pic up the top hole.
Water feeds for heater and your about there
The adapter I used was for the sj so needed the bottom on each side cutting off
Gold Jimny the best colour (sold)
Big red Jimny 32" tyres, arbs, cage 5:1 transfer etc. (Sold)
Grey pick up Jimny
Turbo m13a, arbs, floating rear shafts, disc conversion rear, vented front conversion. 245 70 16. Winch, 3" lift, 4:16 trans hd shafts and CVS
Please Log in or Create an account to join the conversation.
- darthloachie
- Topic Author
- New Member
-
Public
04 Sep 2014 12:35 #123364
by darthloachie
Replied by darthloachie on topic g16b into a jimny - what parts do I need
Thanks James
Please Log in or Create an account to join the conversation.
- darthloachie
- Topic Author
- New Member
-
Public
12 Sep 2014 18:23 #123958
by darthloachie
Replied by darthloachie on topic g16b into a jimny - what parts do I need
hi guys
how do I identify a skinny starter?
is it either of these?
how do I identify a skinny starter?
is it either of these?
Please Log in or Create an account to join the conversation.
Time to create page: 0.165 seconds