×
BigJimnyMeet (North) 2024 (12 Jan 2024)


BigJimnyMeet 2024

14th July 2024
Parkwood Nr. Leeds

Booking now open - Discount for additional vehicles

Click HERE for details

× A place for general chat about the Jimny. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.

Suppliers/Dealers or anyone selling with a commercial view in mind CANNOT post here unless responding to a specific request of a member in a "wanted" post.

Suppliers include people "breaking for spares" on a regular basis, when purchasing spares members should ask a supplier what they contribute to the running of the forum particularly if contacted by a Private Message

Suppliers or Members who have contributed to the forum can be identifed by the
logo.

M series engined 2008 jimny

More
14 Jan 2024 00:09 #253493 by andyrowen
Anyone done the conversion back to manual front hubs and manual transfer lever for 4x4. Electronics on my wife's are shot.

Please Log in or Create an account to join the conversation.

  • Lambert
  • Lambert's Avatar
  • Offline
  • Moderator
  • Moderator
    Registered
  • The quickest Jimny in Harrogate...(that I own)
More
14 Jan 2024 04:25 #253497 by Lambert
Replied by Lambert on topic M series engined 2008 jimny
Yes it's quite straightforward there is even a removable plate in the floor for the lever. However the gearing will be lower as the lever box will be 1.3 to 1 in high not 1 to 1. What are the symptoms that make you think that the electronics are at fault?

Temeraire (2018 quasar grey automatic)
One of the last 200ish of the gen3s, probably.
ADOS Attention Deficit Ooooh Shiny!

Please Log in or Create an account to join the conversation.

More
14 Jan 2024 07:30 #253498 by yakuza
Replied by yakuza on topic M series engined 2008 jimny
Drive shaft differences too isn't it before and after 2005?
I would not be surprised if it was possible to put a gen4 handle assembly where the gen3 actuator is on the Tcase but other than general optimism i have no knowledge if it can be done.

Norway 2005 Jimny M16A VVT, 235 BFG MT, 2" Trailmaster, ARB rear lck, 17%/87% high/low gears.

Please Log in or Create an account to join the conversation.

More
22 Jan 2024 04:36 #253654 by andyrowen
Cannot get 4x4 to engage. Electri motor runs, it's been bench tested, control buttons on dash have been tested and are okay, unsure if the vacuum controlled hubs are working or not

Please Log in or Create an account to join the conversation.

More
22 Jan 2024 06:57 #253656 by yakuza
Replied by yakuza on topic M series engined 2008 jimny
www.bigjimny.com/mediawiki/index.php/4WD..._failure_diagnostics

I found the wiki a very good help as allways.

When there is a vacuum problem the lights on the dash will flash and tell mostly.
Lack of vacuum will result in no engagement and a flashing light when you push the bottom. Could be a leak most likely, but also other faults.

Norway 2005 Jimny M16A VVT, 235 BFG MT, 2" Trailmaster, ARB rear lck, 17%/87% high/low gears.

Please Log in or Create an account to join the conversation.

Time to create page: 0.090 seconds
Powered by Kunena Forum

I hope you enjoy using this forum. Please consider making a donation towards the upkeep of this forum website.

We use cookies to give you the best online experience. Please let us know if you agree to all of these cookies. Accepting the Cookies also accepts the Disclaimers for the website.