×
BigJimnyMeet (North) 2024 (12 Jan 2024)


BigJimnyMeet 2024

14th July 2024
Parkwood Nr. Leeds

Booking now open - Discount for additional vehicles

Click HERE for details

× A place for general chat about the Jimny. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.

Suppliers/Dealers or anyone selling with a commercial view in mind CANNOT post here unless responding to a specific request of a member in a "wanted" post.

Suppliers include people "breaking for spares" on a regular basis, when purchasing spares members should ask a supplier what they contribute to the running of the forum particularly if contacted by a Private Message

Suppliers or Members who have contributed to the forum can be identifed by the
logo.

Remote Gear Change Mechanism - Removal and Service

  • teafortwo0789
  • Topic Author
  • Visitor
  • Visitor
    Public
15 Nov 2011 18:49 #25842 by teafortwo0789
I've got a stiff gear change in 1st. and 2nd. I've lubricated the gear lever from inside the cab, with no real improvement. I've been to my local Suzuki main dealer to see if the gear change was slicker and smooth, compared to mine and it was

I suspect I need to have a go at the remote control.
1. Is it possible / easy to remove the remote with gear box in situ?
2. Any suggestions welcome

Thanks in anticipation.

Please Log in or Create an account to join the conversation.

  • p1ngu32
  • Visitor
  • Visitor
    Public
15 Nov 2011 21:10 #25849 by p1ngu32
Its not too bad to get at you have to work around the propshaft but there is enough room, check that the bolt isnt missing from the rod that is mounted to the back of the gear box through a bush, mine was missing when i got it and made selecting 1st and 2nd a bit difficult, i think its a common problem and there was a recall on it, there isnt alot else to make it stiff if you have greased it.
To remove it completely you need to remove the stick then undo the 2? bolts inside under the gaiter, the 2 bolts from the selector rod and 4 bolts that hold the rear engine mount on to the back of the gearbox and possibly a few other bolts ive forgotten about. There is a section on it in martins changing the clutch write up.

Richard

Please Log in or Create an account to join the conversation.

  • teafortwo0789
  • Topic Author
  • Visitor
  • Visitor
    Public
16 Nov 2011 10:11 #25872 by teafortwo0789
Replied by teafortwo0789 on topic Re: Remote Gear Change Mechanism - Removal and Service
Thank you Richard, I'll give it a go. From Martins Clutch Article I wasn't too sure if I'd need to remove the exhaust pipe etc, so your reply is good news.

Please Log in or Create an account to join the conversation.

  • p1ngu32
  • Visitor
  • Visitor
    Public
16 Nov 2011 10:47 #25873 by p1ngu32
Should be fine to leave the exhaust on i think, maybe give you more room to work if it was out of the way mind you.

Please Log in or Create an account to join the conversation.

  • teafortwo0789
  • Topic Author
  • Visitor
  • Visitor
    Public
16 Nov 2011 11:32 #25875 by teafortwo0789
Replied by teafortwo0789 on topic Re: Remote Gear Change Mechanism - Removal and Service
Richard,
Once again thanks. I've just been checking on the recall notification and you were correct Suzuki did have a recall for that fault. However it was for an earlier model, mine is a 2003. I try to do my home work prior to starting any job, I've found it can save me lot of time and struggling.

Still good advice and this seems a good place to start, so I'll be in the pit this week end and will get back to the forum with the result. The exhaust is fairly new so should not be too hard to get off. I asked the garage to put 'copper slip' on all bolts as they did the job, in anticipation such an eventuality!

Please Log in or Create an account to join the conversation.

Time to create page: 0.091 seconds
Powered by Kunena Forum

I hope you enjoy using this forum. Please consider making a donation towards the upkeep of this forum website.

We use cookies to give you the best online experience. Please let us know if you agree to all of these cookies. Accepting the Cookies also accepts the Disclaimers for the website.