Difference between revisions of "Gearbox R72 rebuild"

From BigJimny Wiki
Jump to navigation Jump to search
Line 106: Line 106:
 
<br clear=all>
 
<br clear=all>
  
 +
A better idea of what you are up against with the output shaft here. None of this was hard to pull off with the splitter and press. Note the blind circlip. There's a couple of these about but actually they weren't much of a problem. Lean on either side with 2 big flathead screwdrivers and they ping off. Sometimes they even remain in sight.
 +
 +
<br clear=all>
 +
[[File:Gb17.jpg|thumb|left|350px|Bearing Splitter]]
 +
<br clear=all>
  
 
=== Torque Settings ===
 
=== Torque Settings ===

Revision as of 20:36, 18 January 2017

Note Icon.pngUse the "Print as PDF" tab above to print


A guide to rebuilding an R72 gearbox

Introduction

The R72 gearbox is was fitted from about 2005. The case splits vertically into three parts. The earlier box splits horizontally.

Bearing failure seems fairly common on these boxes. Many of these were fitted with faulty prop-shafts that allowed oil to leak through the centre cap of the prop, and perhaps oil starvation early in their life contributes to failures. All of the deep groove open bearings on the original box are replaced with metal shielded units in Suzuki's parts which implies there may be a general issue in splashing enough oil around.

Rebuild

Tools

Spanner Icon.png
  • Standard metric sockets and spanners
  • Range of impact sockets used to press in bearings
  • 2 large flat head screw drivers
  • a 2 leg gear puller and/or hydraulic press
  • bearing seperator
  • torque wrench(s) to cover 23-90Nm
  • copper or plastic mallet
  • sturdy metal tube of approx 25mm internal diameter, at least 130mm long; but see text for alternatives



Ideally you'll want a copy of the correct service manual. This gearbox is covered under supplementary service manual 99501-81A010-01E. You might get lucky with Google!

Gearbox Removal

Is covered elsewhere (need to link). When draining the gearbox oil a furry drain plug and chunks of metal are a good sign something has gone wrong in there.

Drain Plug


Dismantling

With the gearbox on your workbench, remove the 4 bolts (black arrows in below picture) holding on the gear change cover and remove. It's sealed with liquid gasket and may need a tap with a soft hammer.

Cover removal


Remove gear shift locating bolts (red arrows in above picture), springs and ball bearings (not shown). There is also a bolt on the opposite side of the case for the reverse gear shaft you need to remove with its spring and bearing.

The bearings can stick in the shafts. If you can't them out at this stage losely refit a bolt in the corresponding hole without the spring so you don't lose the bearing when you start to remove the gear shafts.


Locating bolts


Needs something here about rear case removal

With the rear case off you can now see the long output shaft, and the short counter shaft. The below picture was taken on reassembly with a new sealed bearing on the counter shaft. From the factory this was an open bearing on my 2009 model.


Output shaft


The output shaft lifts away easily. Do this slowly and make sure nothing lose is stuck to the bottom of this ready to fall on the floor.


Output shaft


Looking down on to what is the input shaft, you should be left with the a synchroniser ring (brass colour), under this is a round, lose clip, and in the centre a needle roller bearing. It's worth lifting these out now and keeping safely, in the correct order with your output shaft. They'll only fall out and disappear later when you pull out the input shaft.


Output shaft


Something about removing the mid case here.

Remove the reverse gear. Be careful here, the lever plate (red arrow), connects to one of the shift rods (yellow arrow). If you lift the shift rod it will probably pop off a synchro sleeve on the input shaft, and syncho keys will fall on the floor, and you will be sad.


Reverse lever


Below is a sad syncho sleeve with syncho keys no where to be seen. Don't let the sleeve lift as much as this. You have been warned, etc.


Reverse lever


Next remove the 5th gear shift inverse lever at the base of the shift rods. Just two bolts and lift it out.


5th gear shift inverse lever


At this stage you can release the large circlip at the base of the input shaft and lift away both the input and counter shafts plus the shift rods.


Input and counter shafts


I jumped the gun a bit and got going before dismantling everything. This is the top of the counter shaft. Fairly obvious what is wrong here. In fact this is the only bearing that appeared sub-optimal in my box.


Counter shaft


So I removed it with a hydraulic puller. None of the bearings took much effort to remove. I'd be confident this could be done with a manual puller.


Input and counter shafts


Bearing removal is trickier when the bearing is at the bottom of a shaft. You could possibly have tapped this off from behind. On the output shaft there are bearings either side of the gear and the whole lot needs pulling off. I did them one component at a time using a bearing splitter and a hydraulic press.


Output shaft


This isn't the output shaft, but you get the idea.


Bearing Splitter


A better idea of what you are up against with the output shaft here. None of this was hard to pull off with the splitter and press. Note the blind circlip. There's a couple of these about but actually they weren't much of a problem. Lean on either side with 2 big flathead screwdrivers and they ping off. Sometimes they even remain in sight.


Bearing Splitter


Torque Settings

Full details of the torque settings can be found in the reference data


Page last edited on 18/01/2017 by user Sheepish