×
BigJimnyMeet (North) 2024 (12 Jan 2024)
BigJimnyMeet 2024
14th July 2024
Parkwood Nr. Leeds
14th July 2024
Parkwood Nr. Leeds
Booking now open - Discount for additional vehicles
Click HERE for details
Click HERE for details
×
A place for general chat about the Jimny. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.
Suppliers/Dealers or anyone selling with a commercial view in mind CANNOT post here unless responding to a specific request of a member in a "wanted" post.
Suppliers include people "breaking for spares" on a regular basis, when purchasing spares members should ask a supplier what they contribute to the running of the forum particularly if contacted by a Private Message
Suppliers or Members who have contributed to the forum can be identifed by the logo.
Suppliers/Dealers or anyone selling with a commercial view in mind CANNOT post here unless responding to a specific request of a member in a "wanted" post.
Suppliers include people "breaking for spares" on a regular basis, when purchasing spares members should ask a supplier what they contribute to the running of the forum particularly if contacted by a Private Message
Suppliers or Members who have contributed to the forum can be identifed by the logo.
10 Tonne Press
Less
More
- Posts: 1250
- Thank you received: 116
- Points: 545.00
18 Sep 2017 14:53 #184217
by maverick
Jalapeño, IISY?
10 Tonne Press was created by maverick
I'm thinking about buying one for myself at home ...
Has anyone got one at home and would they recommend it, and where did you buy it from?
Thanks
Brett
Has anyone got one at home and would they recommend it, and where did you buy it from?
Thanks
Brett
Jalapeño, IISY?
Please Log in or Create an account to join the conversation.
- jackonlyjack
- Offline
- Platinum Member
-
Registered
Less
More
- Posts: 2909
- Thank you received: 651
- Points: 8451.00
18 Sep 2017 15:28 #184219
by jackonlyjack
Replied by jackonlyjack on topic 10 Tonne Press
I don't own one but used this many times
www.machinemart.co.uk/p/clarke-csa10ep-1...nomy-hydraulic-floo/
Jack
www.machinemart.co.uk/p/clarke-csa10ep-1...nomy-hydraulic-floo/
Jack
Please Log in or Create an account to join the conversation.
Less
More
- Posts: 1250
- Thank you received: 116
- Points: 545.00
18 Sep 2017 15:41 - 18 Sep 2017 15:43 #184221
by maverick
Jalapeño, IISY?
Replied by maverick on topic 10 Tonne Press
Thanks Jason - Is it good for the Jimny Long Rear Shafts too?
Jalapeño, IISY?
Last edit: 18 Sep 2017 15:43 by maverick.
Please Log in or Create an account to join the conversation.
- jackonlyjack
- Offline
- Platinum Member
-
Registered
Less
More
- Posts: 2909
- Thank you received: 651
- Points: 8451.00
18 Sep 2017 17:20 #184224
by jackonlyjack
Replied by jackonlyjack on topic 10 Tonne Press
Never tried a rear shaft
But you could always remove the bed and use something on the floor
That will give you over 800mm
just make sure its bolted to the floor well
(i have no clue how much pressure you need to fit the bearing/retainer/abs ring)
or get a slimline bed fabricated
But you could always remove the bed and use something on the floor
That will give you over 800mm
just make sure its bolted to the floor well
(i have no clue how much pressure you need to fit the bearing/retainer/abs ring)
or get a slimline bed fabricated
Please Log in or Create an account to join the conversation.
Less
More
- Posts: 1936
- Thank you received: 554
- Points: 7523.00
18 Sep 2017 17:50 #184226
by Riccy
J999 MNY, ULYSSES M18 VVT with ITB's Dyno tested at 130hp
Pickup/tipper, R7me gearbox & 6.4 Rocklobster, 31" Toyo MT, 2x ARB air locker 3.9 diffs in braced axles, 6" total lift, Floating rear conversion, Raptor painted, CB, Recaro's, Caged, etc, etc...
www.youtube.com/user/riclemus
Replied by Riccy on topic 10 Tonne Press
There are loads of copycat ones of the machine mart one linked on ebay. I would avoid it as the design allows for it to push off centre, risking the piece flying out of the machine under heavy pressure! Its essentially a sprungloaded bottle jack design. The ones which have a solid long ram are much safer.
This is the one i have (but it defo wont do the rear bearings as not long enough, does everything else happily and safely)...
www.machinemart.co.uk/p/clarke-csa10bb-10-tonne-bench-press/
Riccy
This is the one i have (but it defo wont do the rear bearings as not long enough, does everything else happily and safely)...
www.machinemart.co.uk/p/clarke-csa10bb-10-tonne-bench-press/
Riccy
J999 MNY, ULYSSES M18 VVT with ITB's Dyno tested at 130hp
Pickup/tipper, R7me gearbox & 6.4 Rocklobster, 31" Toyo MT, 2x ARB air locker 3.9 diffs in braced axles, 6" total lift, Floating rear conversion, Raptor painted, CB, Recaro's, Caged, etc, etc...
www.youtube.com/user/riclemus
Please Log in or Create an account to join the conversation.
Less
More
- Posts: 3727
- Thank you received: 923
- Points: 9981.00
18 Sep 2017 18:10 #184228
by X8GGY
Replied by X8GGY on topic 10 Tonne Press
I've just switched between eBay accounts, and when I logged out it knew I'd just been on the MachineMart site looking at this, and it popped up and said use "EBAY20" at the checkout to get 20% off !
Please Log in or Create an account to join the conversation.
Less
More
- Posts: 3727
- Thank you received: 923
- Points: 9981.00
18 Sep 2017 18:26 #184229
by X8GGY
My garage use a length of seamless tube they stole off me!
I've got some in my man-cave I can cut to size for you mate
Dave
Replied by X8GGY on topic 10 Tonne Press
maverick wrote: Thanks Jason - Is it good for the Jimny Long Rear Shafts too?
My garage use a length of seamless tube they stole off me!
I've got some in my man-cave I can cut to size for you mate
Dave
Please Log in or Create an account to join the conversation.
18 Sep 2017 21:10 - 18 Sep 2017 21:26 #184235
by mlines
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Replied by mlines on topic 10 Tonne Press
I use this one...www.machinemart.co.uk/p/clarke-csa10bb-10-tonne-bench-press/
Did both my rear bearings yesterday by standing it on a workmate and dropping the shafts through the gap, simples!
Gauge was reading around 2 tonnes at the peak
Did both my rear bearings yesterday by standing it on a workmate and dropping the shafts through the gap, simples!
Gauge was reading around 2 tonnes at the peak
Martin
2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses
Last edit: 18 Sep 2017 21:26 by mlines.
Please Log in or Create an account to join the conversation.
18 Sep 2017 21:11 #184236
by kirkynut
The underdog often starts the fight, and occasionally the upper dog deserves to win - Edgar Watson Howe.
My Jimny Thread Here: www.bigjimny.com/index.php/forum/8-my-ji...on-continues?start=0
Replied by kirkynut on topic 10 Tonne Press
Surely the free standing floor mounted 12T one they do will press the bearing onto the long shaft?
Kirkynut
Kirkynut
The underdog often starts the fight, and occasionally the upper dog deserves to win - Edgar Watson Howe.
My Jimny Thread Here: www.bigjimny.com/index.php/forum/8-my-ji...on-continues?start=0
Please Log in or Create an account to join the conversation.
Time to create page: 0.148 seconds