×
BigJimnyMeet (North) 2024 (12 Jan 2024)


BigJimnyMeet 2024

14th July 2024
Parkwood Nr. Leeds

Booking now open - EARLY BIRD DISCOUNTED PRICE

Click HERE for details

× A place for more technical discussions. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.

Re:Driveshaft alloy spacer

More
13 Nov 2019 08:14 #215586 by giacomom
Hi all,

I have a doubt
a to fit a + 60/70 mm lift kit I would like to know where the driveshaft alloy spacer is mounted :
front or rear and transfer or axle side ?
thank you

Giacomo

Please Log in or Create an account to join the conversation.

More
15 Nov 2019 06:17 #215641 by giacomom
Replied by giacomom on topic Driveshaft alloy spacer
Hi,

41 views and no answers......
Is it a too technical request ?
thank you

Giacomo

Please Log in or Create an account to join the conversation.

  • Riccy
  • Riccy's Avatar
  • Offline
  • Banned
  • Banned
    Registered
  • J999 MNY Bashing around Carlisle
More
15 Nov 2019 07:23 #215642 by Riccy
Replied by Riccy on topic Re:Driveshaft alloy spacer
It’s not too technical, rather too specific.

A kit you have bought should come with some instructions or support from the seller, however that doesn’t seem to be the case.

I use a small spacer on the intermediate prop, but this is to do with the rock lobster transfer box.

Prop spacers for front/rear props would always go at the transfer box end, but they are not the best solution. Generally you will end up changing to some HD props eventually as the UJs on standard props are not designed to run at such high angles.


Sent from my iPhone using Tapatalk

J999 MNY, ULYSSES M18 VVT with ITB's Dyno tested at 130hp

Pickup/tipper, R7me gearbox & 6.4 Rocklobster, 31" Toyo MT, 2x ARB air locker 3.9 diffs in braced axles, 6" total lift, Floating rear conversion, Raptor painted, CB, Recaro's, Caged, etc, etc...

www.youtube.com/user/riclemus

Please Log in or Create an account to join the conversation.

More
15 Nov 2019 07:45 #215643 by giacomom
Replied by giacomom on topic Re:Driveshaft alloy spacer
Hi Riccy and thank you for answer

the kit has no assembly instructions but the seller has informed me that the spacer must be to fit front driveshaft axle side ...... why ?

" Prop spacers for front/rear props would always go at the transfer box end, "
so what do i do ?

Giacomo

Please Log in or Create an account to join the conversation.

  • Riccy
  • Riccy's Avatar
  • Offline
  • Banned
  • Banned
    Registered
  • J999 MNY Bashing around Carlisle
More
15 Nov 2019 10:51 #215652 by Riccy
Replied by Riccy on topic Driveshaft alloy spacer
Try it and see. If you notice the UJs on prop binding up then swap it around.


Sent from my iPhone using Tapatalk

J999 MNY, ULYSSES M18 VVT with ITB's Dyno tested at 130hp

Pickup/tipper, R7me gearbox & 6.4 Rocklobster, 31" Toyo MT, 2x ARB air locker 3.9 diffs in braced axles, 6" total lift, Floating rear conversion, Raptor painted, CB, Recaro's, Caged, etc, etc...

www.youtube.com/user/riclemus

Please Log in or Create an account to join the conversation.

More
15 Nov 2019 23:33 #215678 by jackonlyjack
I'm with Riccy transfer box end on a gen3
If you have a gen4 it may need to fit at diff end :unsure:

Please Log in or Create an account to join the conversation.

Time to create page: 0.100 seconds
Powered by Kunena Forum

I hope you enjoy using this forum. Please consider making a donation towards the upkeep of this forum website.

We use cookies to give you the best online experience. Please let us know if you agree to all of these cookies. Accepting the Cookies also accepts the Disclaimers for the website.