× A place for more technical discussions. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.

M13A - M16A

More
14 Aug 2019 17:40 #212092 by spj907
M13A - M16A was created by spj907
Hi, I'm going to swap the M13A engine in my 2000 jimny for the M16A found in the Liana, both non VTT. There are a few around, but the Question is how can you tell the vvt from the non vvt? Is it true ALL the lianas had non vvt engines? I believe i read that somewhere. Pictures showing the difference would be great but a bit of an ask!?!?

Please Log in or Create an account to join the conversation.

  • Lambert
  • Lambert's Avatar
  • Away
  • Moderator
  • Moderator
    Registered
  • The quickest Jimny in Harrogate...(that I own)
More
15 Aug 2019 04:17 #212108 by Lambert
Replied by Lambert on topic M13A - M16A
Vvt engines have a pronounced step/bulge in the front of the rocker cover on the left side as viewed from the front of the car. None vvt is smooth across.

Dreadnaught (black 2011)

Please Log in or Create an account to join the conversation.

More
15 Aug 2019 17:30 #212133 by spj907
Replied by spj907 on topic M13A - M16A
Brilliant, just what i needed to know. I've checked out a few pictures on line and can see the difference, thanks Lambert.
I could be back for a bit more help when i start this, but looking through some of the other posts on this subject it looks fairly straightforward....time will tell!

Please Log in or Create an account to join the conversation.

More
16 Aug 2019 11:11 #212163 by Jjbradshaw1
Replied by Jjbradshaw1 on topic M13A - M16A
Where are you based? I've got an M16A with only 27k on it that I bought last summer off a forum member. I'm looking to sell my Jimny so its not likely to get used, if you're willing to collect its yours for £200. I've even got the gaskets you'll need and a new filter as well as a liana intake.

Please Log in or Create an account to join the conversation.

More
16 Aug 2019 13:17 #212169 by spj907
Replied by spj907 on topic M13A - M16A
Hi, seemed to have private messaged you!

Please Log in or Create an account to join the conversation.

More
16 Aug 2019 13:36 #212170 by Jjbradshaw1
Replied by Jjbradshaw1 on topic M13A - M16A
Ah, bit of a trek for you I'm afraid unless you have courier contacts. I am up in Newcastle, NE42 6HW

Please Log in or Create an account to join the conversation.

More
16 Aug 2019 13:44 #212171 by spj907
Replied by spj907 on topic M13A - M16A
Oh, shame. I could look into couriers...never used them before though.

Please Log in or Create an account to join the conversation.

More
16 Aug 2019 16:46 #212173 by mlines
Replied by mlines on topic M13A - M16A
Look for pallet carriers

Sent from my Pixel 2 XL using Tapatalk

Martin

2003 M13 early KAP build.
3" Trailmaster lift with 1.5 Spacers on front
Customised winch bumper and roll cage
235/85R16 Maxxis Bighorns on 16" Rims, 4:1 Rocklobster, Rear ARB locker and on-board air
Corrected arms all-round, rear disks, Recaro seats and harnesses

Please Log in or Create an account to join the conversation.

Time to create page: 0.124 seconds
Powered by Kunena Forum

I hope you enjoy using this forum. Please consider making a donation towards the upkeep of this forum website.