× A place for general chat about the Jimny. Please make sure you post in the correct section on the site, this way it keeps the site tidy AND ensures you get a more relevant answer.

Suppliers/Dealers or anyone selling with a commercial view in mind CANNOT post here unless responding to a specific request of a member in a "wanted" post.

Suppliers include people "breaking for spares" on a regular basis, when purchasing spares members should ask a supplier what they contribute to the running of the forum particularly if contacted by a Private Message

Suppliers or Members who have contributed to the forum can be identifed by the
logo.[/size][/color][/b]

Quick bit of help please

More
17 May 2020 07:02 #222364 by me101
Hi, does anyone know what is behind the top of the firewall? Wanting to remove the weather strip and drill some holes, will I catch any wires / pipes? Looking just between aircon pipes and the black motor.

Thanks,
Attachments:

Please Log in or Create an account to join the conversation.

  • Riccy
  • Riccy's Avatar
  • Online
  • Site Sponsor
  • Site Sponsor
    Registered
  • J999 MNY Bashing around Carlisle
More
17 May 2020 07:50 #222365 by Riccy
Replied by Riccy on topic Quick bit of help please
Thats the scuttle panel area where the wiper arm linkage is. The black motor is the wiper motor. Its easy enough to pop the scuttle panel off to see (remove wipers and plastic fixings, lift up). Holes need to be sealed into that area as the water collected on the windscreen drains down into there.

Lower down (aircon pipe level) will get you into the cabin (if thats the aim). Remove the glovebox and have a look for the aircon pipes to see where you could drill. The ECU wiring comes in behind the ABS pump so be careful of that. I think theres a load of plastic stuff for the heater/fans to be careful of too.

J999 MNY, ULYSSES M18 VVT with ITB's Dyno tested at 130hp

Pickup/tipper, R7me gearbox & 4.3 Rocklobster, 31" Toyo MT, 2x ARB 3.9 diffs in braced axles, 6" total lift, Floating rear conversion, Raptor painted, CB, Recaro's, Caged, etc, etc...

www.youtube.com/user/riclemus

Please Log in or Create an account to join the conversation.

More
17 May 2020 07:59 #222366 by me101
Replied by me101 on topic Quick bit of help please
Sounds busy round there! It is the small thin rubber strip I am looking to remove a section of, and drill down (wanting to screw a bracket on (all may become clear at a later date if it goes to plan!).

Please Log in or Create an account to join the conversation.

More
17 May 2020 10:39 #222379 by me101
Replied by me101 on topic Quick bit of help please
2nd quick question - where is the wiper fuse, and does it affect anything else?

Please Log in or Create an account to join the conversation.

More
17 May 2020 12:04 #222390 by kirkynut
Replied by kirkynut on topic Quick bit of help please
By your right knee there is a panel held in place by 2 screws. Unscrew them and remove the panel by unclipping it. In your original handbook that comes with the car is a diagram with which fuse does what.

Kirkynut

The underdog often starts the fight, and occasionally the upper dog deserves to win - Edgar Watson Howe.

My Jimny Thread Here: www.bigjimny.com/index.php/forum/8-my-ji...on-continues?start=0

Please Log in or Create an account to join the conversation.

More
17 May 2020 12:06 #222391 by me101
Replied by me101 on topic Quick bit of help please
I think I've seen that before, will have a look, cheers

Please Log in or Create an account to join the conversation.

Time to create page: 0.079 seconds
Powered by Kunena Forum

I hope you enjoy using this forum. Please consider making a donation towards the upkeep of this forum website.

We use cookies to give you the best online experience. Please let us know if you agree to all of these cookies. Accepting the Cookies also accepts the Disclaimers for the website.