Difference between revisions of "Clutch replacement"

From BigJimny Wiki
Jump to navigation Jump to search
m (Category adjustment)
 
(12 intermediate revisions by 2 users not shown)
Line 1: Line 1:
{{note|Use the "Print as PDF" tab above to print}}
+
{{intro-notes}}
= A guide to changing the clutch. =
+
 
 +
 
 
== Introduction ==
 
== Introduction ==
 +
  
 
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.
 
It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gearbox under the car, it is a very tight fit in the transmission tunnel.
 
  
So what are the symptoms of a worn clutch/clutch mechanism:
+
Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gear box under the car. It is a very tight fit in the transmission tunnel.
 +
 
 +
The symptoms of a worn clutch/clutch mechanism:
 
* Judder as clutch is released
 
* Judder as clutch is released
 
* Slipping as engine power is applied
 
* Slipping as engine power is applied
Line 12: Line 15:
 
* Bearing squeal or rumble when clutch pedal pressed.
 
* Bearing squeal or rumble when clutch pedal pressed.
  
== Changing the Clutch ==
+
 
 +
If this hasn’t put you off then its time to start work.
 +
 
 +
{{note|This article was written based on a RHD petrol Jimny configuration. LHD petrol Jimnys should be quite similar. However, diesel (DDiS) Jimnys have many smaller and larger differences concerning the parts mentioned in this article. Therefore, there might be significant deviations compared to this guide.}}
 +
 
 +
 
 
=== Tools ===
 
=== Tools ===
 +
 +
 
{{tools|<ul><li> Standard metric sockets and spanners</li><li>Assorted screwdrivers</li><li>Breaker bar</li><li>Clutch alignment tool</li><li>Strops to pull engine forward</li><li>10mm Square Drain plug socket</ul>
 
{{tools|<ul><li> Standard metric sockets and spanners</li><li>Assorted screwdrivers</li><li>Breaker bar</li><li>Clutch alignment tool</li><li>Strops to pull engine forward</li><li>10mm Square Drain plug socket</ul>
 
<br>
 
<br>
Line 19: Line 29:
 
<br clear=all>
 
<br clear=all>
  
== Removing Interior Items ==
 
  
If this hasn’t put you off then its time to start work. It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!
+
== General procedure ==
There are two ways of changing the clutch, one is to take the engine and gearbox out and the other is to drop the gearbox off. The Suzuki factory manual suggests the gearbox dropping method so that is the way I have gone.
+
 
 +
 
 +
It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!
 +
 
 +
There are two ways of changing the clutch, one is to take the engine and gear box out and the other is to drop the gear box off. The Suzuki factory manual suggests the gear box dropping method so that is the way I have gone.
  
 
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.
 
The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.
  
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gearbox housing as these are difficult.
+
If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gear box housing as these are difficult.
 +
 
 +
 
 +
== Removing Items ==
 +
 
 +
 
 +
=== Introduction ===
 +
 
  
 
Starting inside the car it is necessary to remove the console, the gear lever and the transfer box lever.
 
Starting inside the car it is necessary to remove the console, the gear lever and the transfer box lever.
 +
 +
 
=== Centre Console ===
 
=== Centre Console ===
  
[[File:Figure 1. Removing the Centre Console.png|thumb|left|350px|Figure 1. Removing the Centre Console]]
+
 
To remove the gearbox lever you have to remove the centre console. This is held on by four screws on the side at the front and back. The console then lifts out.
+
[[File:Clutch replacement guide - figure 01 - removing the centre console.png|thumb|left|512px|Figure 01 - removing the centre console]]
Mine was more of a problem as I have a switch panel fitted so I then needed to remove the gearlever before the console would come completely away, but this has to be done at some point anyway.
+
 
 +
* To remove the gear box lever, you have to remove the centre console.
 +
* This is held on by four screws on the side at the front and back.
 +
* The console then lifts out.
 +
* Mine was more of a problem as I have a switch panel fitted.
 +
* Therefore, I then needed to remove the gear lever before the console would come completely away, but this has to be done at some point anyway.
 
<br clear=all>
 
<br clear=all>
 +
  
 
=== Gear levers ===
 
=== Gear levers ===
[[File:Figure 2. Removing the Gearlever.png|thumb|left|350px|Figure 2. Removing the Gearlever]]
+
 
Pull the gaiter away to reveal the three bolt heads around the base of the gearlever, undo the bolts and carefully lift out the gearstick, note that there is a small spring and a cup that should not be lost!
+
 
 +
[[File:Clutch replacement guide - figure 02 - removing the gear lever.png|thumb|left|512px|Figure 02 - removing the gear lever]]
 +
 
 +
* Pull the gaiter away to reveal the three bolt heads around the base of the gearlever.
 +
* Undo the bolts and carefully lift out the gearstick.
 +
* Note that there is a small spring and a cup that should not be lost!
 
<br clear=all>
 
<br clear=all>
 +
  
 
=== Lower Gaiter ===
 
=== Lower Gaiter ===
[[File:Figure 3. Removing the lower Gaiter.png|thumb|left|250px|Figure 3. Removing the lower Gaiter]]
+
 
With the console removed you will then see a frame that holds in a second gaiter. Simply undo the bolts and lift the frame clear.
+
 
 +
[[File:Clutch replacement guide - figure 03 - removing the lower gaiter.png|thumb|left|592px|Figure 03 - removing the lower gaiter]]
 +
 
 +
* With the console removed, you will then see a frame that holds in a second gaiter.
 +
* Simply undo the bolts and lift the frame clear.
 
<br clear=all>
 
<br clear=all>
 +
  
 
=== Transfer Lever ===
 
=== Transfer Lever ===
[[File:Figure 4. Removing the Transfer Lever Knob.png|thumb|left|250px|Figure 4. Removing the Transfer Lever Knob]]
+
 
If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level. First locate the small screw at the rear of the transfer knob and remove it.
+
 
 +
[[File:Clutch replacement guide - figure 04 - removing the transfer lever knob.png|thumb|left|512px|Figure 04 - removing the transfer lever knob]]
 +
 
 +
* If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level.
 +
* First locate the small screw at the rear of the transfer knob and remove it.
 
<br clear=all>
 
<br clear=all>
[[File:Figure 5. Removing the Transfer Level Gaiter.png|thumb|left|250px|Figure 5. Removing the Transfer Level Gaiter]]
+
 
Unscrew the frame around the gaiter and pull the frame and gaiter clear.
+
[[File:Clutch replacement guide - figure 05 - removing the transfer level gaiter.png|thumb|left|592px|Figure 05 - removing the transfer level gaiter]]
 +
 
 +
* Unscrew the frame around the gaiter and pull the frame and gaiter clear.
 
<br clear=all>
 
<br clear=all>
  
== Draining the Oil ==
+
 
[[File:Figure 6. Gearbox Drain Plugs.png|thumb|left|250px|Figure 6. Gearbox Drain Plugs]]
+
=== Draining the Oil ===
Move outside the car and disconnect the negative cable at battery.
+
 
Now drain the oil from the gearbox and transfer box, if you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.
+
 
On my Jimny the drain plugs are square and therefore a SQUARE 10MM drain plug socket should be used, however the square end of a 3/8 socket driver fits if you are pushed. Always undo the filler plug first because if the filler is stuck you do not want to drain the oil and not be able to fill it again. The gearbox filler is hidden up the side of the gearbox and lack of space is a problem
+
[[File:Clutch replacement guide - figure 06 - gear box drain plugs.png|thumb|left|624px|Figure 06 - gear box drain plugs]]
 +
 
 +
* Move outside the car and disconnect the negative cable at battery.
 +
* Now drain the oil from the gear box and transfer box.
 +
* If you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.
 +
* On my Jimny, the drain plugs are square and therefore a SQUARE 10MM drain plug socket should be used.
 +
* However, the square end of a 3/8 socket driver fits if you are pushed.
 +
* Always undo the filler plug first, because if the filler is stuck you do not want to drain the oil and not be able to fill it again.
 +
* The gear box filler is hidden up the side of the gear box and lack of space is a problem.
 
<br clear=all>
 
<br clear=all>
  
== Removing Front Exhaust Section ==
 
  
=== Exhaust ===
+
=== Removing Front Exhaust Section ===
[[File:Figure 7. Transfer Box Fillers and Connectors.png|thumb|left|250px|Figure 7. Transfer Box Fillers and Connectors]]
+
 
On the Transfer Box disconnect the 4WD switch wire at coupler and unclamp harness. Then disconnect the speed sensor coupler.
+
 
 +
==== Exhaust ====
 +
 
 +
 
 +
[[File:Clutch replacement guide - figure 07 - transfer box fillers and connectors.png|thumb|left|720px|Figure 07 - transfer box fillers and connectors]]
 +
 
 +
* On the Transfer Box, disconnect the 4WD switch wire at coupler and unclamp harness.
 +
* Then disconnect the speed sensor coupler.
 
<br clear=all>
 
<br clear=all>
[[File:Figure 8. Exhaust Bolts.png|thumb|left|250px|Figure 8. Exhaust Bolts]]
+
 
Now remove the front section of the exhaust pipe. This is held in place by pairs of springs with bolts inside. Due to the heat and stress the front bolts were really, really difficult to move. So much so I think there is real possibility of shearing them on some cars. There is a pair at the front and a pair at the back.
+
[[File:Clutch replacement guide - figure 08 - exhaust bolts.png|thumb|left|480px|Figure 08 - exhaust bolts]]
 +
 
 +
* Now remove the front section of the exhaust pipe.
 +
* This is held in place by pairs of springs with bolts inside.
 +
* Due to the heat and stress, the front bolts were really, really difficult to move.
 +
* So much so, I think there is real possibility of shearing them on some cars.
 +
* There is a pair at the front and a pair at the back.
 
<br clear=all>
 
<br clear=all>
  
=== Lambda Sensor ===
+
 
[[File:Figure 9. Lambda Sensor on Converter.png|thumb|left|250px|Figure 9. Lambda Sensor on Converter]]
+
==== Lambda Sensor ====
Do not lift the exhaust of the rubber hangers yet. There is a Lambda sensor connected to the top of the catalytic converter.
+
 
 +
 
 +
[[File:Clutch replacement guide - figure 09 - lambda sensor on converter.png|thumb|left|480px|Figure 09 - lambda sensor on converter]]
 +
 
 +
* Do not lift the exhaust of the rubber hangers yet.
 +
* There is a Lambda sensor connected to the top of the catalytic converter.
 
<br clear=all>
 
<br clear=all>
[[File:Lambda Sensor Connector Behind Here.png|thumb|left|250px|Lambda Sensor Connector Behind Here]]
+
 
This needs to be disconnected. The Suzuki manual shows the sensor being unscrewed from the top of the converter. However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in. Instead I followed the wiring back up to behind the engine. Just behind the head on the passenger side is a set of connectors, unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).
+
[[File:Clutch replacement guide - figure 10 - lambda sensor connector behind here.png|thumb|left|480px|Figure 10 - lambda sensor connector behind here]]
With the Lambda sensor disconnected you can pull the front exhaust section off the rubber mounts.
+
 
 +
* This needs to be disconnected.
 +
* The Suzuki manual shows the sensor being unscrewed from the top of the converter.
 +
* However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in.
 +
* Instead, I followed the wiring back up to behind the engine.
 +
* Just behind the head on the passenger side is a set of connectors.
 +
* Unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).
 +
* With the Lambda sensor disconnected, you can pull the front exhaust section off the rubber mounts.
 
<br clear=all>
 
<br clear=all>
  
== Removing the Prop shafts, Transfer Box & Gearbox Remote Mechanism ==
 
  
 
=== Prop shafts ===
 
=== Prop shafts ===
[[File:Mark the Propshaft.png|thumb|left|250px|Mark the Propshaft]]
+
 
Now remove the propshafts. On each shaft paint some marks so they can be rebolted to the flanges in the correct position when you are re-building it. Paint all the flanges and also mark the sliding joint in the front propshaft. Remove the FRONT propshaft FIRST, followed by the Gearbox/Transfer box shaft SECOND. Where possible do the REAR propshaft LAST. Why! – because all the propshaft bolts are quite tight and therefore you need to hold the propshafts in place whilst you try to undo the bolts. As the front hubs are vacuum operated there is no easy way to lock the props if you have disconnected the rear first. With the rear prop still on the rear wheels keep the system locked. I found out this trick the hard way.
+
 
<br clear=all>
+
[[File:Clutch replacement guide - figure 11 - mark the propeller shaft.png|thumb|left|640px|Figure 11 - mark the propeller shaft]]
 +
 
 +
* Now remove the propeller shafts.
 +
* Paint some marks on each shaft paint, so they can be rebolted to the flanges in the correct position when you are re-building it.
 +
* Paint all the flanges and also mark the sliding joint in the front propeller shaft.
 +
* Remove the FRONT propeller shaft FIRST, followed by the gear box/transfer box shaft SECOND.
 +
* Where possible do the REAR propeller shaft LAST.
 +
* Reason - all the propeller shaft bolts are quite tight, and therefore you need to hold the propeller shafts in place whilst you try to undo the bolts.
 +
* As the front hubs are vacuum operated, there is no easy way to lock the propeller shafts if you have disconnected the rear first.
 +
* With the rear propeller shaft still on the rear wheels, keep the system locked.
 +
* I found out this trick the hard way.
 +
 
 +
{{warning|It is very important to mount all the propeller shafts back exactly as they were, because they were balanced for that position in the factory!}}
 +
 
  
 
=== Transfer Box ===
 
=== Transfer Box ===
[[File:Figure 10. Transfer mounts.png|thumb|left|250px|Figure 10. Transfer mounts]]
+
 
Now undo the 3 large mounting nuts on the transfer box mount and the 4 bolts on the mounting flange. Now the transfer box should lift down.
+
 
 +
[[File:Clutch replacement guide - figure 12 - transfer box mounts.png|thumb|left|312px|Figure 12 - transfer box mounts]]
 +
 
 +
* Undo the 3 large mounting nuts on the transfer box mount and the 4 bolts on the mounting flange.
 +
* Now the transfer box should lift down.
 
<br clear=all>
 
<br clear=all>
  
[[File:Figure 11. Transfer Mounts.png|thumb|left|250px|Figure 11. Transfer Mounts]]
+
[[File:Clutch replacement guide - figure 13 - transfer box mounts.png|thumb|left|656px|Figure 13 - transfer box mounts]]
 
<br clear=all>
 
<br clear=all>
  
=== Gearbox Remote Mechanism ===
+
 
[[File:Figure 12. Gearbox Remote Mechanism.png|thumb|left|250px|Figure 12. Gearbox Remote Mechanism]]
+
=== Gear box Remote Mechanism ===
Now for the complex bit. The Jimny has a remote gearbox mechanism bolted onto the rear of the gearbox and this needs to be removed. It’s probably easier to see the part after it has been removed as it is clearer what you are trying to achieve. Note this is the top view, you will normally be underneath!
+
 
 +
[[File:Clutch replacement guide - figure 14 - gear box remote mechanism.png|thumb|left|768px|Figure 14 - gear box remote mechanism]]
 +
 
 +
* Now for the complex bit!
 +
* The Jimny has a remote gear box mechanism bolted onto the rear of the gear box and this needs to be removed.
 +
* It’s probably easier to see the part after it has been removed, as it is clearer what you are trying to achieve.
 +
* Note this is the top view, you will normally be underneath and quite nervous!
 
<br clear=all>
 
<br clear=all>
[[File:Figure 13. Remote Mechanism in place.png|thumb|left|250px|Figure 13. Remote Mechanism in place]]
+
 
Remove gear shift control joint bolt and extension rod bolt.
+
[[File:Clutch replacement guide - figure 15 - remote mechanism in place.png|thumb|left|800px|Figure 15 - remote mechanism in place]]
 +
 
 +
* Remove gear shift control joint bolt and extension rod bolt.
 
<br clear=all>
 
<br clear=all>
  
== Removing the Engine Mounting Bolts, Starter Motor and Clutch Cable ==
 
  
 
=== Engine Mounting ===
 
=== Engine Mounting ===
  
Remove the Engine Rear Mounting bolts (Three of them, one either side and one in the rubber bit). This is the mount under the gearbox that rests on the chassis crossmember.
 
  
Using a long socket extension, reach into the remote mechanism and undo the 4 bolts that connect it to the gearbox. These are hard to reach.
+
Remove the Engine Rear Mounting bolts. There are three of them, one either side and one in the rubber bit. This is the mount under the gear box that rests on the chassis crossmember.
 +
 
 +
Using a long socket extension, reach into the remote mechanism and undo the 4 bolts that connect it to the gear box. These are hard to reach.
 +
 
 +
The entire mechanism should then be removeable complete with the mounts. Also unbolt all the other metal bits (including the exhaust mounting rubber) from the rear cross member as you will need to squeeze the gear box out later on.
  
The entire mechanism should then be removeable complete with the mounts. Also unbolt all the other metal bits (including the exhaust mounting rubber) from the rear cross member as you will need to squeeze the Gearbox out later on.
 
  
 
=== Reversing Switch ===
 
=== Reversing Switch ===
[[File:Figure 14. Gearbox Reverse Switch.png|thumb|left|250px|Figure 14. Gearbox Reverse Switch]]
+
 
Now remove the reversing light switch. This is on top of the gearbox towards the front and was more accessible from under the bonnet by reaching down the back of the engine on the passenger side (UK). Tie it up out of the way.
+
 
 +
[[File:Clutch replacement guide - figure 16 - gear box reverse switch.png|thumb|left|480px|Figure 16 - gear box reverse switch]]
 +
 
 +
* Now remove the reversing light switch.
 +
* This is on top of the gear box towards the front.
 +
* It was more accessible from under the bonnet by reaching down the back of the engine on the passenger side (UK).
 +
* Tie it up out of the way.
 
<br clear=all>
 
<br clear=all>
 +
  
 
=== Starter Motor ===
 
=== Starter Motor ===
[[File:Figure 15. Starter Motor (from underneath car).png|thumb|left|250px|Figure 15. Starter Motor (from underneath car)]]
+
 
Now for the next difficult task, removing the starter motor. Clearly Suzuki never considered that a starter motor may go wrong and need replacing as it is in one of the most in-accessible places. First of all check that you have disconnected the battery. Laying under the car reach up the drivers side of the engine and unbolt the two bolts holding the motor in place and easy it back. There is no need to remove it completely and no need to undo all the cables attached to in.
+
 
 +
[[File:Clutch replacement guide - figure 17 - starter motor (from underneath car).png|thumb|left|480px|Figure 17 - starter motor (from underneath car)]]
 +
 
 +
* Now for the next difficult task, removing the starter motor.
 +
* Clearly Suzuki never considered that a starter motor may go wrong and need replacing as it is in one of the most in-accessible places.
 +
* First of all, check that you have disconnected the battery.
 +
* Laying under the car, reach up the drivers side of the engine and unbolt the two bolts holding the motor in place and easy it back.
 +
* There is no need to remove it completely and no need to undo all the cables attached to in.
 
<br clear=all>
 
<br clear=all>
 +
  
 
=== Clutch Cable ===
 
=== Clutch Cable ===
[[File:Figure 16. Clutch cable (unhooked).png|thumb|left|250px|Figure 16. Clutch cable (unhooked)]]
+
 
We are nearly there now. Remove plastic clutch housing cap and prise the end of the clutch cable from clutch release fork. Then undo the two bolts holding the clutch cable to the transmission and withdraw the clutch cable assembly. Also remove the small tin-plate on the bottom front of the clutch housing held on by a pair of small 10mm bolts.
+
 
 +
[[File:Clutch replacement guide - figure 18 - clutch cable (unhooked).png|thumb|left|480px|Figure 18 - clutch cable (unhooked)]]
 +
 
 +
* We are nearly there now.
 +
* Remove plastic clutch housing cap and prise the end of the clutch cable from clutch release fork.
 +
* Then undo the two bolts holding the clutch cable to the transmission and withdraw the clutch cable assembly.
 +
* Also remove the small tin-plate on the bottom front of the clutch housing held on by a pair of small 10mm bolts.
 
<br clear=all>
 
<br clear=all>
  
== Seperating Gearbox away From Engine ==
 
  
The official workshop manual now says to undo the bellhousing bolts and lower the gearbox away from the engine. Whoever wrote this must have been smoking something very exotic. The first problem is to locate all the bolts on the bellhousing as they are well hidden. Take a close look at the picture below and locate all the bolts.
+
=== Separating the gear box away from the engine ===
 +
 
 +
 
 +
The official workshop manual now says to undo the bellhousing bolts and lower the gear box away from the engine. Whoever wrote this must have been smoking something very exotic, or was planning on quitting the job soon.
 +
 
 +
[[File:Clutch replacement guide - figure 19 - gear box bolts.png|thumb|left|360px|Figure 19 - gear box bolts]]
  
[[File:Figure 17. Gearbox bolts.png|thumb|left|250px|Figure 17. Gearbox bolts]]
+
* The first problem is to locate all the bolts on the bellhousing as they are well hidden.
 +
* Take a close look at the picture and locate all the bolts.
 
<br clear=all>
 
<br clear=all>
  
The next problem is undoing them as there is no room to get a socket set in. I had to use a complex combination of extensions and flex joints from two socket sets to get to a couple of the bolts. Also note that there is very little chance of the gearbox falling off once the bolts are undone so don’t spend a lot of time supporting it.
 
  
Separating the gearbox from the engine can be a real pain (literally). The gearbox is located on studs and corrosion can hold it in place. I had to hit the bellhousing edge with a large hammer (protecting the metal with a wooden block) before it would separate.
+
The next problem is undoing them as there is no room to get a socket set in. I had to use a complex combination of extensions and flex joints from two socket sets to get to a couple of the bolts. Also note that there is very little chance of the gear box falling off once the bolts are undone so don’t spend a lot of time supporting it.
[[File:Figure 18. Pulling the engine forward with strap.png|thumb|left|250px|Figure 18. Pulling the engine forward with strap]]
+
 
Once it is separated you have to drop the gearbox down. The transmission tunnel is so tight that this appears to be a near impossible task. I had to jack the engine forward to gain as much room as possible. You will also find that the gearbox will move backwards a little way in the tunnel, this means you can then open a useful gap around the clutch.
+
Separating the gear box from the engine can be a real pain (literally). The gear box is located on studs and corrosion can hold it in place. I had to hit the bellhousing edge with a large hammer (protecting the metal with a wooden block) before it would separate.
 +
 
 +
[[File:Clutch replacement guide - figure 20 - pulling the engine forward with strap.png|thumb|left|480px|Figure 20 - pulling the engine forward with strap]]
 +
 
 +
* Once it is separated you have to drop the gear box down.
 +
* The transmission tunnel is so tight that this appears to be a near impossible task.
 +
* I had to jack the engine forward to gain as much room as possible.
 +
* You will also find that the gear box will move backwards a little way in the tunnel.
 +
* This means you can then open a useful gap around the clutch.
 
<br clear=all>
 
<br clear=all>
  
[[File:Figure 19. Gap between gearbox and clutch with engine pulled forward.png|thumb|left|250px|Figure 19. Gap between gearbox and clutch with engine pulled forward]]
+
[[File:Clutch replacement guide - figure 21 - gap between gear box and clutch with engine pulled forward.png|thumb|left|480px|Figure 21 - gap between gear box and clutch with engine pulled forward]]
Some people have changed the clutch using just this gap. Instead, I undid the clutch cover bolts and removed the clutch assembly with the gearbox still in place. Removing the clutch then meant there was just enough room for the gearbox to be pulled out.
+
 
 +
* Some people have changed the clutch using just this gap.
 +
* Instead, I undid the clutch cover bolts and removed the clutch assembly with the gear box still in place.
 +
* Removing the clutch then meant there was just enough room for the gear box to be pulled out.
 
<br clear=all>
 
<br clear=all>
 +
  
 
== Replacing the Clutch ==
 
== Replacing the Clutch ==
  
Within the clutch kit should be a new cover, new plate and new release bearing.
+
 
[[File:Figure 20. Clutch Release Bearing.png|thumb|left|250px|Figure 20. Clutch Release Bearing]]
+
[[File:Clutch replacement guide - figure 22 - clutch release bearing.png|thumb|left|608px|Figure 22 - clutch release bearing]]
The old release bearing is removed by prising the spring clip out of the mounting and sliding it out of the spring. Re-assembly is just as easy, make sure that the splines are lightly greased and the inside of the release bearing where it slides on the shaft is greased (not the bearing itself – this should be lubricated by the factory).
+
 
 +
* Within the clutch kit should be a new cover, new plate and new release bearing.
 +
* The old release bearing is removed by prising the spring clip out of the mounting and sliding it out of the spring.
 +
* Re-assembly is just as easy.
 +
* Make sure that the splines are lightly greased and the inside of the release bearing where it slides on the shaft is greased (not the bearing itself – this should be lubricated by the factory).
 
<br clear=all>
 
<br clear=all>
 +
  
 
Put grease on the moving points of the clutch release arm as well.
 
Put grease on the moving points of the clutch release arm as well.
  
 +
[[File:Clutch replacement guide - figure 23 - wrong release bearing is on right.png|thumb|left|480px|Figure 23 - wrong release bearing is on right]]
  
 
+
* I originally purchased a cheap kit (CPK1086) from Ebay, this was before the Bigjimny shop!
[[File:Figure 21. Wrong Release Bearing is on Right.png|thumb|left|250px|Figure 21. Wrong Release Bearing is on Right]]
+
* The quality seems OK (it is stamped as being made by AISIN – who supply Suzuki with parts).
I originally purchased a cheap kit (CPK1086) from ebay, this was before the Bigjimny shop!. The quality seems ok (it is stamped as being made by AISIN – who supply Suzuki with parts), the only issue being that it was supplied with the incorrect release bearing. The company immediately shipped the correct bearing free of charge and assured me that the correct bearing should have been in the kit. Also note that the new plate has 4 springs whilst the old one has 3, again I have been assured that this is ok.
+
* The only issue being that it was supplied with the incorrect release bearing.
 +
* The company immediately shipped the correct bearing free of charge and assured me that the correct bearing should have been in the kit.
 +
* Also note that the new plate has 4 springs whilst the old one has 3, again I have been assured that this is OK.
 
<br clear=all>
 
<br clear=all>
  
[[File:Figure 22. New Clutch Plate on left.png|thumb|left|250px|Figure 22. New Clutch Plate on left]]
+
[[File:Clutch replacement guide - figure 24 - new clutch plate on left.png|thumb|left|480px|Figure 24 - new clutch plate on left]]
 
<br clear=all>
 
<br clear=all>
  
[[File:Figure 23. New clutch cover on left.png|thumb|left|250px|Figure 23. New clutch cover on left]]
+
[[File:Clutch replacement guide - figure 25 - new clutch cover on left.png|thumb|left|480px|Figure 25 - new clutch cover on left]]
 
<br clear=all>
 
<br clear=all>
  
Assemble the new clutch mechanism using a clutch alignment tool (I got mine cheap - £1 – as it was a girlie pink colour and had remained unsold in the shop for a long time). With this tool you assemble the clutch off the car and then lift the whole unit into place and bolt down the clutch cover to the flywheel. Remove clutch alignment tool.
+
[[File:Clutch replacement guide - figure 26 - clutch assembled.png|thumb|left|480px|Figure 26 - clutch assembled]]
  
[[File:Figure 24. Clutch Assembled.png|thumb|left|250px|Figure 24. Clutch Assembled]]
+
* Assemble the new clutch mechanism using a clutch alignment tool.
 +
* I got mine cheap - £1 – as it was a girlie pink colour and had remained unsold in the shop for a long time.
 +
* With this tool you assemble the clutch off the car and then lift the whole unit into place and bolt down the clutch cover to the flywheel.
 +
* Remove clutch alignment tool.
 
<br clear=all>
 
<br clear=all>
  
[[File:Figure 25. Clutch with alignment tool.png|thumb|left|250px|Figure 25. Clutch with alignment tool]]
+
[[File:Clutch replacement guide - figure 27 - clutch with alignment tool.png|thumb|left|448px|Figure 27 - clutch with alignment tool]]
 
<br clear=all>
 
<br clear=all>
  
[[File:Figure 26. Clutch back in place.png|thumb|left|250px|Figure 26. Clutch back in place]]
+
[[File:Clutch replacement guide - figure 28 - clutch back in place.png|thumb|left|480px|Figure 28 - clutch back in place]]
 
<br clear=all>
 
<br clear=all>
  
Wipe a layer of grease around the mating face of the gearbox, this should mean it doesn’t stick in the future and should make it easier to re-assemble.
+
[[File:Clutch replacement guide - figure 29 - grease the mounting face of the gear box.png|thumb|left|480px|Figure 29 - grease the mounting face of the gear box]]
  
[[File:Figure 27. Grease the mounting face of the gearbox.png|thumb|left|250px|Figure 27. Grease the mounting face of the gearbox]]
+
* Wipe a layer of grease around the mating face of the gear box.
 +
* This should mean it doesn’t stick in the future and should make it easier to re-assemble.
 
<br clear=all>
 
<br clear=all>
  
== Refitting the Gearbox ==
 
  
With the engine still jacked forward it should be possible to jack the gearbox back into place using the weight of the car to help force it into position. Before trying to mate it back with the clutch allow the engine to drop back into its proper position (not too far back) – this will make it easier to align.
+
== Extended breathers ==
 +
 
 +
 
 +
=== Introduction ===
  
It should now be possible to wiggle the gearbox forward. FIRST OF ALL CHECK NOTHING IS IN THE WAY – I failed to notice the reversing light switch had fallen down and I severed the cable which had become trapped. Fitting the gearbox is one of those tasks where you will have repeated attempts to get it to go and then it will suddenly “click” – it will need lots of tiny jiggles to creep it onto the studs.
 
  
Refit all the bolts that hold the gearbox in place (use Copper Grease on the bolts to make it easier next time!)
+
{{note|See the wiki article [[Transmission breathers|'''"Transmission breathers"''']] for more info about the installation of these breathers.}}
  
Now it’s a matter of going back through the steps previously to refit everything.
 
  
Note that you may want to fit extended breathers to the gearbox whilst it is in bits. The picture below shows the rubber pipe that is the normal breather (minus a plastic cap which has already fallen off!). The later models have an extended breather already, and it's another good candidate for slipping between the gearbox and engine while you are trying to refit it.
+
=== Gear box breather ===
  
Simply slide some pipe onto the tub and extend the breather to a higher point on the car.
 
  
[[File:Figure 28. Gearbox breather.png|thumb|left|250px|Figure 28. Gearbox breather]]
+
* Note that you may want to fit extended breathers to the gear box while it is dismounted from the vehicle.
<br clear=all>
+
* This is the perfect opportunity to do it.
 +
 
 +
 
 +
=== Transfer box breathers ===
 +
 
 +
 
 +
* If the transfer box is also dismantled, adding extended breathers to it would also be an excellent idea.
 +
* The transfer box has two breathers.
 +
* The process is similar and simple like when doing the gear box breathers.
 +
 
 +
 
 +
== Refitting everything back ==
 +
 
 +
 
 +
=== Introduction ===
 +
 
 +
 
 +
This is generally a reverse procedure compared to dismantling. Enjoy doing it.
 +
 
 +
Below are some notes on specifics.
 +
 
 +
 
 +
=== Refitting the gear box ===
 +
 
 +
 
 +
With the engine still jacked forward it should be possible to jack the gear box back into place using the weight of the car to help force it into position. Before trying to mate it back with the clutch allow the engine to drop back into its proper position (not too far back) – this will make it easier to align.
 +
 
 +
It should now be possible to wiggle the gear box forward.
 +
 
 +
{{warning|'''First of all check that nothing is in the way''' – I failed to notice the reversing light switch had fallen down and I severed the cable which had become trapped.}}
 +
 
 +
 
 +
Fitting the gear box is one of those tasks where you will have repeated attempts to get it to go and then it will suddenly “click” – it will need lots of tiny jiggles to creep it onto the studs.
 +
 
 +
Refit all the bolts that hold the gear box in place (use Copper Grease on the bolts to make it easier next time!)
  
  
 
{{Edited}}
 
{{Edited}}
[[Category:Howto]][[Category:Drivechain]]
+
 
 +
[[Category:Howto - gen3]]
 +
[[Category:Drivechain - gen3]]

Latest revision as of 13:34, 21 February 2019

Note Icon.pngThe content of any article might be expanded / improved in the future - revisit it sometimes.
Note Icon.pngSeen a mistake? Know something that isn't written? Edit and change this article yourself!
Note Icon.pngSome images in the article (if present) can be enlarged by clicking on them.


Introduction

It is inevitable that at some point you will have to face changing the clutch. It dips in and out of the mud on a regular basis as the bell-housing is not sealed. Eventually the clutch thrust bearing will start rattling and the action will become stiff and heavy.

Changing the clutch on a Jimny seems to be not for the faint hearted. It’s a very physical task and it is not pleasant struggling with the gear box under the car. It is a very tight fit in the transmission tunnel.

The symptoms of a worn clutch/clutch mechanism:

  • Judder as clutch is released
  • Slipping as engine power is applied
  • Burning smell or smoke from under car
  • Bearing squeal or rumble when clutch pedal pressed.


If this hasn’t put you off then its time to start work.

Note Icon.pngThis article was written based on a RHD petrol Jimny configuration. LHD petrol Jimnys should be quite similar. However, diesel (DDiS) Jimnys have many smaller and larger differences concerning the parts mentioned in this article. Therefore, there might be significant deviations compared to this guide.



Tools

Spanner Icon.png
  • Standard metric sockets and spanners
  • Assorted screwdrivers
  • Breaker bar
  • Clutch alignment tool
  • Strops to pull engine forward
  • 10mm Square Drain plug socket




General procedure

It goes without saying that you should jet-wash the underside of the car if possible to remove as much of the muck before it drops on you!

There are two ways of changing the clutch, one is to take the engine and gear box out and the other is to drop the gear box off. The Suzuki factory manual suggests the gear box dropping method so that is the way I have gone.

The factory manual suggests it is not necessary to remove the transfer box, but I have removed it as you will need all the space you can get, I thoroughly recommend that you also remove the transfer box.

If you have the luxury of a bit of time then spray the visible bolts with WD40 a day or so before. In particular you should try and spray the bolts holding the exhaust front section and the bolts around the gear box housing as these are difficult.


Removing Items

Introduction

Starting inside the car it is necessary to remove the console, the gear lever and the transfer box lever.


Centre Console

Figure 01 - removing the centre console
  • To remove the gear box lever, you have to remove the centre console.
  • This is held on by four screws on the side at the front and back.
  • The console then lifts out.
  • Mine was more of a problem as I have a switch panel fitted.
  • Therefore, I then needed to remove the gear lever before the console would come completely away, but this has to be done at some point anyway.



Gear levers

Figure 02 - removing the gear lever
  • Pull the gaiter away to reveal the three bolt heads around the base of the gearlever.
  • Undo the bolts and carefully lift out the gearstick.
  • Note that there is a small spring and a cup that should not be lost!



Lower Gaiter

Figure 03 - removing the lower gaiter
  • With the console removed, you will then see a frame that holds in a second gaiter.
  • Simply undo the bolts and lift the frame clear.



Transfer Lever

Figure 04 - removing the transfer lever knob
  • If you are removing the Transfer Box then you need to remove the gaiter etc. around the Transfer Box Level.
  • First locate the small screw at the rear of the transfer knob and remove it.


Figure 05 - removing the transfer level gaiter
  • Unscrew the frame around the gaiter and pull the frame and gaiter clear.



Draining the Oil

Figure 06 - gear box drain plugs
  • Move outside the car and disconnect the negative cable at battery.
  • Now drain the oil from the gear box and transfer box.
  • If you are not doing any work on the transfer box then it is not strictly necessary to drain the oil providing you keep it upright to stop the oil coming out of the lever hole.
  • On my Jimny, the drain plugs are square and therefore a SQUARE 10MM drain plug socket should be used.
  • However, the square end of a 3/8 socket driver fits if you are pushed.
  • Always undo the filler plug first, because if the filler is stuck you do not want to drain the oil and not be able to fill it again.
  • The gear box filler is hidden up the side of the gear box and lack of space is a problem.



Removing Front Exhaust Section

Exhaust

Figure 07 - transfer box fillers and connectors
  • On the Transfer Box, disconnect the 4WD switch wire at coupler and unclamp harness.
  • Then disconnect the speed sensor coupler.


Figure 08 - exhaust bolts
  • Now remove the front section of the exhaust pipe.
  • This is held in place by pairs of springs with bolts inside.
  • Due to the heat and stress, the front bolts were really, really difficult to move.
  • So much so, I think there is real possibility of shearing them on some cars.
  • There is a pair at the front and a pair at the back.



Lambda Sensor

Figure 09 - lambda sensor on converter
  • Do not lift the exhaust of the rubber hangers yet.
  • There is a Lambda sensor connected to the top of the catalytic converter.


Figure 10 - lambda sensor connector behind here
  • This needs to be disconnected.
  • The Suzuki manual shows the sensor being unscrewed from the top of the converter.
  • However, the sensor has been subject to red hot heat, water and mud, therefore mine was firmly rusted in.
  • Instead, I followed the wiring back up to behind the engine.
  • Just behind the head on the passenger side is a set of connectors.
  • Unbolt the connector mounting bracket and prise the Lambda connector apart (this is very stiff as well!).
  • With the Lambda sensor disconnected, you can pull the front exhaust section off the rubber mounts.



Prop shafts

Figure 11 - mark the propeller shaft
  • Now remove the propeller shafts.
  • Paint some marks on each shaft paint, so they can be rebolted to the flanges in the correct position when you are re-building it.
  • Paint all the flanges and also mark the sliding joint in the front propeller shaft.
  • Remove the FRONT propeller shaft FIRST, followed by the gear box/transfer box shaft SECOND.
  • Where possible do the REAR propeller shaft LAST.
  • Reason - all the propeller shaft bolts are quite tight, and therefore you need to hold the propeller shafts in place whilst you try to undo the bolts.
  • As the front hubs are vacuum operated, there is no easy way to lock the propeller shafts if you have disconnected the rear first.
  • With the rear propeller shaft still on the rear wheels, keep the system locked.
  • I found out this trick the hard way.

Warning Icon.pngIt is very important to mount all the propeller shafts back exactly as they were, because they were balanced for that position in the factory!



Transfer Box

Figure 12 - transfer box mounts
  • Undo the 3 large mounting nuts on the transfer box mount and the 4 bolts on the mounting flange.
  • Now the transfer box should lift down.


Figure 13 - transfer box mounts



Gear box Remote Mechanism

Figure 14 - gear box remote mechanism
  • Now for the complex bit!
  • The Jimny has a remote gear box mechanism bolted onto the rear of the gear box and this needs to be removed.
  • It’s probably easier to see the part after it has been removed, as it is clearer what you are trying to achieve.
  • Note this is the top view, you will normally be underneath and quite nervous!


Figure 15 - remote mechanism in place
  • Remove gear shift control joint bolt and extension rod bolt.



Engine Mounting

Remove the Engine Rear Mounting bolts. There are three of them, one either side and one in the rubber bit. This is the mount under the gear box that rests on the chassis crossmember.

Using a long socket extension, reach into the remote mechanism and undo the 4 bolts that connect it to the gear box. These are hard to reach.

The entire mechanism should then be removeable complete with the mounts. Also unbolt all the other metal bits (including the exhaust mounting rubber) from the rear cross member as you will need to squeeze the gear box out later on.


Reversing Switch

Figure 16 - gear box reverse switch
  • Now remove the reversing light switch.
  • This is on top of the gear box towards the front.
  • It was more accessible from under the bonnet by reaching down the back of the engine on the passenger side (UK).
  • Tie it up out of the way.



Starter Motor

Figure 17 - starter motor (from underneath car)
  • Now for the next difficult task, removing the starter motor.
  • Clearly Suzuki never considered that a starter motor may go wrong and need replacing as it is in one of the most in-accessible places.
  • First of all, check that you have disconnected the battery.
  • Laying under the car, reach up the drivers side of the engine and unbolt the two bolts holding the motor in place and easy it back.
  • There is no need to remove it completely and no need to undo all the cables attached to in.



Clutch Cable

Figure 18 - clutch cable (unhooked)
  • We are nearly there now.
  • Remove plastic clutch housing cap and prise the end of the clutch cable from clutch release fork.
  • Then undo the two bolts holding the clutch cable to the transmission and withdraw the clutch cable assembly.
  • Also remove the small tin-plate on the bottom front of the clutch housing held on by a pair of small 10mm bolts.



Separating the gear box away from the engine

The official workshop manual now says to undo the bellhousing bolts and lower the gear box away from the engine. Whoever wrote this must have been smoking something very exotic, or was planning on quitting the job soon.

Figure 19 - gear box bolts
  • The first problem is to locate all the bolts on the bellhousing as they are well hidden.
  • Take a close look at the picture and locate all the bolts.



The next problem is undoing them as there is no room to get a socket set in. I had to use a complex combination of extensions and flex joints from two socket sets to get to a couple of the bolts. Also note that there is very little chance of the gear box falling off once the bolts are undone so don’t spend a lot of time supporting it.

Separating the gear box from the engine can be a real pain (literally). The gear box is located on studs and corrosion can hold it in place. I had to hit the bellhousing edge with a large hammer (protecting the metal with a wooden block) before it would separate.

Figure 20 - pulling the engine forward with strap
  • Once it is separated you have to drop the gear box down.
  • The transmission tunnel is so tight that this appears to be a near impossible task.
  • I had to jack the engine forward to gain as much room as possible.
  • You will also find that the gear box will move backwards a little way in the tunnel.
  • This means you can then open a useful gap around the clutch.


Figure 21 - gap between gear box and clutch with engine pulled forward
  • Some people have changed the clutch using just this gap.
  • Instead, I undid the clutch cover bolts and removed the clutch assembly with the gear box still in place.
  • Removing the clutch then meant there was just enough room for the gear box to be pulled out.



Replacing the Clutch

Figure 22 - clutch release bearing
  • Within the clutch kit should be a new cover, new plate and new release bearing.
  • The old release bearing is removed by prising the spring clip out of the mounting and sliding it out of the spring.
  • Re-assembly is just as easy.
  • Make sure that the splines are lightly greased and the inside of the release bearing where it slides on the shaft is greased (not the bearing itself – this should be lubricated by the factory).



Put grease on the moving points of the clutch release arm as well.

Figure 23 - wrong release bearing is on right
  • I originally purchased a cheap kit (CPK1086) from Ebay, this was before the Bigjimny shop!
  • The quality seems OK (it is stamped as being made by AISIN – who supply Suzuki with parts).
  • The only issue being that it was supplied with the incorrect release bearing.
  • The company immediately shipped the correct bearing free of charge and assured me that the correct bearing should have been in the kit.
  • Also note that the new plate has 4 springs whilst the old one has 3, again I have been assured that this is OK.


Figure 24 - new clutch plate on left


Figure 25 - new clutch cover on left


Figure 26 - clutch assembled
  • Assemble the new clutch mechanism using a clutch alignment tool.
  • I got mine cheap - £1 – as it was a girlie pink colour and had remained unsold in the shop for a long time.
  • With this tool you assemble the clutch off the car and then lift the whole unit into place and bolt down the clutch cover to the flywheel.
  • Remove clutch alignment tool.


Figure 27 - clutch with alignment tool


Figure 28 - clutch back in place


Figure 29 - grease the mounting face of the gear box
  • Wipe a layer of grease around the mating face of the gear box.
  • This should mean it doesn’t stick in the future and should make it easier to re-assemble.



Extended breathers

Introduction

Note Icon.pngSee the wiki article "Transmission breathers" for more info about the installation of these breathers.



Gear box breather

  • Note that you may want to fit extended breathers to the gear box while it is dismounted from the vehicle.
  • This is the perfect opportunity to do it.


Transfer box breathers

  • If the transfer box is also dismantled, adding extended breathers to it would also be an excellent idea.
  • The transfer box has two breathers.
  • The process is similar and simple like when doing the gear box breathers.


Refitting everything back

Introduction

This is generally a reverse procedure compared to dismantling. Enjoy doing it.

Below are some notes on specifics.


Refitting the gear box

With the engine still jacked forward it should be possible to jack the gear box back into place using the weight of the car to help force it into position. Before trying to mate it back with the clutch allow the engine to drop back into its proper position (not too far back) – this will make it easier to align.

It should now be possible to wiggle the gear box forward.

Warning Icon.pngFirst of all check that nothing is in the way – I failed to notice the reversing light switch had fallen down and I severed the cable which had become trapped.



Fitting the gear box is one of those tasks where you will have repeated attempts to get it to go and then it will suddenly “click” – it will need lots of tiny jiggles to creep it onto the studs.

Refit all the bolts that hold the gear box in place (use Copper Grease on the bolts to make it easier next time!)



Page last edited on 21/02/2019 by user Bosanek